M-F Manufacturing Co., Inc. - 817- 281-9488 / Fax 817-281-9498

Page 1 of 3 - Regular Liquid Plastic

Supplier:
M-F Manufacturing Co., Inc
P.O. Box 820442
Fort Worth, TX 76182
Phone: 817-281-9488
Fax: 817-281-9498

MATERIAL SAFETY DATA SHEET
Issue Date: July 7, 2008

Product Trade Name: Regular Liquid Plastic
Product Trade Number: 2116LP, 2132LP, 2228LP, 2228LP-5, 2228LP-55
Product Class: Polyvinyl Chloride-Plastisol
Chemical Name: N/A
Chemical Family: Plastisol (PVC Compound)
Application Field: N/A
I. Physical Data
Boiling Point (760mm. Hg): None
Freezing Point: -54 Degrees Fahrenheit
Vapor Density (Air = 1): N/A
Vapor Pressure At 20 Degrees C.: Nil
Specific Gravity (H2O = 1): .97
Water Solubility (%By Weight): Insoluble
Percent Volatiles By Volume: Less than 1.0
Evaporation Rate (Butyl Acetate = 1): (N/A)
Appearance: Viscous Liquid
Odor: Mild Petroleum
PH: N/A
II. Hazardous Ingredients
Material Percent Threshold Limit Values (units)
Vinyl Chloride Monomer .0005 5PPM
III. Reactivity Data
Stability: Stable
Conditions to avoid: N/A
Incompatibility: Oxidizing agents
Polymerization: Will not occur
Conditions to avoid: N/A
Hazardous Decomposition Products: Carbon Dioxide, Carbon Monoxide & Hydrogen Chloride at elevated temperatures.
IV. Fire and Explosion Hazard Data
Flash Point: 460 Degrees Fahrenheit
Flammable Limits: N/A
Extinguishing Media: Carbon Dioxide, Dry Chemical, Foam.
Special Fire Fighting Procedures: Fire Fighters and others who may be exposed to products of combustion should wear Full Protective clothing and use approved self-contained breathing apparatus.
Unusual Fire and Explosion Hazards: When forced to burn, this product will decompose and emit toxic fumes containing Carbon Dioxide, carbon Monoxide, Hydrogen Chloride and possibly minor amounts of Aromatic or Aliphatic Hydrocarbons.

Page 2 of 3 - Regular Liquid Plastic

V. Health Hazard Data
Oral Toxicity: Not established
Eye Irritation: Not established
Skin Irritation: Not established
Symptoms of Exposure: No immediate effect. Fumes emitted during fusion may be eye and skin irritant. Degradation products are skin, eye and lung irritants and some people have an allergic response.
Primary Route of Entry: Swallowing. Skin Contact. Inhalation of mist. In the case of fire do not inhale
fume and vapor. Move windward.
Emergency First Aid: Flush eyes with large amounts of water. Remove contaminated clothing. Clean
contaminated skin by washing with soap and water. If irritation of eyes and/or skin
occurs, see a physician. After inhalation: remove person to fresh air. If swallowed,
seek advice of a physician immediately. Caution: Do not place anything in the
mouth of an unconscious person.
Threshold Limit Value: Not established
OSHA Threshold Limit Value: Not available
VI. Special Protection Information
Eye protection: Chemical splash goggles
Respiratory Protection: Use adequate ventilation. In restricted ventilation areas use NIOSH or MSHA approved respirators.
Protective Gloves: Chemical resistant Gloves
Skin Protection: Neoprene or Nitrile rubber gloves
Other Protection: Neoprene apron, Neoprene or Nitrile rubber boots.
VII. Special Precautions
Hygienic Practices: While working do not smoke, eat, drink. Exercise good hygiene.
Handling and Storage: Change contaminated clothing.
After Working: Clean whole body properly.
Storage: Keep drums closed. Provide sufficient ventilation. Do not store near food.
Other Precautions: Avoid contact with eyes, skin and clothing. Although not a hazard, this product should not be stored in direct sun-light or at extreme temperatures. Avoid ingestion and prolonged or repeated skin contact. Wash hands with soap and water before eating or smoking.
VIII. Environmental Protection Procedures
Spill Response: For clean-up: Eliminate all sources of ignition. Keep product from spreading and reclaim large quantities. Collect small amounts with suitable absorbent, such as
sand, earth, or humus. Keep out of sewers and other public water systems. Use
appropriate protective clothing and equipment.
Waste Disposal: Dispose of in accordance with local, state and federal regulations. Designated landfill
subject to local, state and federal regulations.
IX. Transportation and Labeling
DOT Proper Shipping Name: Not applicable
IMDG Class: Not applicable
ICAO Class: Not applicable
Technical name: None
X. Warnings.
Avoid breathing vapor
Avoid contact with skin and eyes
Exercise good hygiene
Keep container closed
Use adequate ventilation.
Wash thoroughly after handling.

Page 3 of 3 - Regular Liquid Plastic

U.S. TSCA Inventory: Registered
E C C E I N E C S: Registered
Japan M I T I: N/E
Australia A I C S: N/E
All information given in this data sheet is to the best of our knowledge accurate, as of the date hereof. However, it is given WITHOUT ACCEPTANCE OF LIABILITY FOR LOSS , DAMAGE OR INJURY TO BUYER OR TO THIRD PARTIES arising out of their use.

DISCLAIMER: In no event will M-F Manufacturing Company., Inc. be responsible for damages of any nature whatsoever resulting from the use of or reliance upon information. No representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information or the product to which information refers.

N/A means: Not Applicable; N/E means: Not Established.
N/D means: Not Determined.

M-F Manufacturing Co., Inc. | 4424 Mclean Road | Ft. Worth, TX 76117-1819 | 817- 281-9488 / Fax 817-281-9498